设为首页    收藏本站

保定华庆钢模具厂
      产品列表
生态护坡模具
水泥件模具
隔离带钢模具
检查井钢模具
标志桩钢模具
化粪池钢模具
井盖模具
围墙板钢模具
方涵模具
流水槽钢模具
      资质荣誉
      联系我们
保定华庆钢模具厂
地 址:保定市东城工业区
电 话:18831266588
联系人:边经理
传 真:0312-8103818
在线QQ:107108222@qq.com
行业新闻

水泥隔离墩模具在循环使用中的注意事项

[关闭该页][设为首页][添加收藏][发送朋友][打印][ ]

水泥隔离墩模具实际操作中的技巧要点是不能够疏忽的,一般来说往往正是这些技巧要点却会影响的到隔离带的成型质量,首先便是泥浆的质量,泥浆是需要大量注入到水泥隔离带模具中的,并且成批隔离带的生产对于泥浆的需求量也会非常的大,因此泥浆的混合状态是非常重要的,通常情况下采用的是水泥、混凝土浇筑到模具中,需要提前大概五到七个小时开始进行泥浆的混合,在各种材料添加的时候同时注入清水,不断的对这些原材料进行搅拌,一直到没有颗粒的状态,并且清水也要在搅拌的过程中进行适量的添加,过稀或者是过稠都不合适。另外是震动工具的采用,一般合格的厂家中会准备震动平台以及振动棒两种工具,但是相对从型号与使用方式进行分析,其实建议使用振动棒完成排气的步骤,一是水泥隔离带模具搬运比较的不变,容易出现泥浆泄露的情况,二是振动平台如果放置大型号的钢模具,受重状态可能达不到标准,所以综合来看使用振动棒进行排气是一个非常不错的选择。

The key points in the practical operation of cement isolation pier mold can not be ignored. Generally speaking, it is these key points that will affect the molding quality of the isolation belt. The first is the quality of mud. Mud needs to be injected into the mold of cement isolation belt in large quantities, and the demand for mud in batch production of isolation belt will be very large, so the mixing of mud is very difficult The state is very important. Usually, cement and concrete are poured into the mold. The slurry should be mixed about five to seven hours in advance. When various materials are added, clean water should be injected at the same time, and these raw materials should be continuously stirred until there are no particles. In addition, clean water should be added appropriately during the mixing process, Too thin or too thick is not suitable. The other is the use of vibration tools. Generally, qualified manufacturers will prepare vibration platform and vibrator. However, based on the analysis of model and use mode, it is recommended to use vibrator to complete the steps of exhaust. First, the handling of cement isolation belt mold is relatively stable, which is prone to mud leakage. Second, if large steel mold is placed on the vibration platform In general, it is a very good choice to exhaust with vibrator.

水泥隔离墩模具多次的应用会造成表面磨损情况的严重,生锈面积也会逐步扩大,其实模具的应用都会有一些痕迹,但是这些都是正常的情况,只要没有危机质量的问题,一般钢模具都是可以长时间进行使用的,那应该如何减少模具的使用痕迹呢,并且延长模具的应用时间,首先要确保模具是正常使用的,每个加工步骤都是正确额,满足了常规的应用目的。接下来是对中央隔离带模具的使用保护工作是不可缺少的,在模具中提前进行刷油,再去注入泥浆,这样模具内一层油膜就可以将含水的混凝土进行阻隔了,含水量较高的泥浆不会与模具直接进行接触,自然模具内壁的生锈问题也就减轻了。水泥隔离墩模具可循环使用次数都是在三百次往上,每次的加工要严格遵守行业规定的步骤,在进行脱模的时候不能够大力拆卸模具,也不可以使用锤子一类的工具对模具进行接触,需要先将螺栓从模具中取下来,在将一块一块的模具拆开就可以了,整个过程会比较的简单,吊装出隔离带就可以了。

The application of cement isolation pier mold for many times will cause serious surface wear, and the rust area will gradually expand. In fact, the application of mold will have some traces, but these are normal situations. As long as there is no quality crisis, the general steel mold can be used for a long time. How to reduce the use traces of mold and prolong the service life of mold Application time, first of all to ensure that the mold is in normal use, each processing step is correct, to meet the normal application purpose. The next step is to protect the use of the mold of the central isolation belt. It is indispensable to brush oil in advance in the mold, and then inject mud. In this way, a layer of oil film in the mold can block the concrete with water content. The mud with higher water content will not directly contact with the mold, and the rusting problem of the inner wall of the natural mold will be reduced. Every time the mold can be removed from the central part of the mold, the bolt can be removed from the mold for one time without using the hammer It's simpler. Just lift out the isolation belt.


【上一个】 隔离墩模具厂家祝贺开工大吉 【下一个】 公路隔离墩模具的用途及操作方式


 · 隔离墩模具厂家祝贺开工大吉 · 水泥隔离墩模具在循环使用中的注意事项
 · 高速隔离墩模具的使用步骤及作用 · 水泥隔离墩模具的基本介绍
 · 水泥隔离墩模具的制作具体要求 · 高速隔离墩模具产品的重要作用
 · 水泥隔离墩模具的制作特点及型号 · 水泥隔离墩模具行业如何在市场中寻求新突破
 · 水泥隔离墩模具的出模方式 · 高速隔离墩模具的拆装步骤
 · 高速隔离墩模具 · 高速隔离墩模具
 · 水泥隔离墩模具的基本知识 · 高速隔离墩模具的设计和拆模方法
 · 怎么通过互联网来挑选优质的隔离墩模具厂家

隔离墩模具-水泥隔离墩模具-高速隔离墩模具—保定华庆钢模具厂 |防撞墙模具|沟盖板模具|流水槽钢模具|检查井钢模具|